Welcome Guest. Sign inor Signup

P0507 OBD2 Code: Idle Control System (IAC) RPM Higher Than Expected

Posted by on May 1, 2018 | 0 Comments

engine light

What does the P0507 code mean?

The P0507 trouble code is being triggered when the idle control system RPM is Higher than expected. All modern engines do have a desired idle rpm, usually between 600-1000 rpm. The control unit is using an active monitoring and adjusting the throttle body to achieve these RPMs. If the Idle RPM is getting over these values and the max adjustment values of the engine control unit, the control unit will trigger this as an error code.

The P0507 code is a common code for vehicles equipped with an electronic throttle body. Newer vehicles do normally use an electronic throttle body. An electronic throttle body is just like it sounds, it’s electronic instead of the old throttle bodies with wires between the gas pedal and the throttle body. An electronic throttle body uses sensors on the gas pedal and an electric engine in the throttle body to give you the desired amount of acceleration. But it does not mean that this trouble code has to be a faulty throttle body, it can have a lot of other causes also.

 

CodeDescriptionCommon CausesPossible Solutions
p0507Idle Control System (IAC) RPM Higher Than ExpectedA vacuum/intake leak (Most common)

Faulty/Stuck EGR (Exhaust Gas Recirculation)

Faulty PCV valve (Positive Crankcase Ventilation)

Faulty/Damaged/Dirty Throttle body

Faulty EVAP (Evaporative Emission)

Faulty IAC (idle air controller)

Faulty Power Steering Switch

Faulty Accelerator Pedal
Fix Vacuum/air leaks ( First step )

Clean the throttle body ( Second step )

Basic Setting / Reset adaptions of the throttle body ( Third Step )

Replace PCV Valve

Replace EVAP vent valve

Replace IAC

Replace Throttle body

Replace Power Steering Switch

Replace Accelerator Pedal

Repair Possible Wiring Issues

 

P0507 Symptoms

The most common symptom of this trouble code is that you will notice that your idle RPM is higher than usual. You will probably also experience a Check Engine Light. You can also have other symptoms like misfires and rough idle and acceleration if it is a lean/rich mixture that is triggering the P0507 code.

  • High Idle RPM
  • Rough Idle
  • Jumping Idle
  • Check Engine Light
  • Rough acceleration

 

Possible Causes

  • A vacuum/intake leak (Most common)
  • Faulty/Stuck EGR (Exhaust Gas Recirculation)
  • Faulty PCV valve (Positive Crankcase Ventilation)
  • Faulty/Damaged/Dirty Throttle body
  • Faulty EVAP (Evaporative Emission)
  • Faulty IAC (idle air controller)
  • Faulty Power Steering Switch
  • Faulty Accelerator Pedal

 

Possible Solutions

  • Fix Vacuum/air leaks ( First step )
  • Clean the throttle body ( Second step )
  • Basic Setting / Reset adaptions of the throttle body ( Third Step )
  • Replace PCV Valve
  • Replace EVAP vent valve
  • Replace IAC
  • Replace Throttle body
  • Replace Power Steering Switch
  • Replace Accelerator Pedal
  • Repair Possible Wiring Issues

 

How to diagnose the P0507 code

This way to diagnose the code is used by the most professional mechanics, for these tasks you may need some required tools to do a fast and easy troubleshooting. Always connect a car charger before you are connecting your OBD2 scanner and other diagnostic tools. Low voltage may damage your control units and give errors.

1. Connect an OBD2 Code scanner and verify the P0507 code and check for other trouble codes

2. Check the Live data of the Idle Control Valve/Throttle body to see if these are correct. Check the position sensor of the accelerator pedal to make sure it is correct.

3. If there are not any other trouble codes stored, check and listen for any vacuum leaks around the intake system. If no vacuum leaks can be seen or heard, you can use a starter spray gas or any other flammable spray and spray it carefully around the intake when the car is at idle. If the engine RPMs rises when spraying, you have a leak somewhere in that area. Remember to do this with care and always have a fire extinguisher close to you.
Professional mechanics use smoke machine leak testers to find this kind of faults very fast and easy without any risk of fire.

4. If no leaks were detected, check if the throttle body is dirty inside. If you find it dirty, remove the throttle body if possible and clean it with brake cleaner or any other strong cleaner. Make sure it gets 100% clean

5. After the throttle body is cleaned, you do normally have to do a basic setting and adaption reset of the throttle body to learn the new values of the clean throttle body. You can do this with an OBD2 Code scanner. The most cheaper OBD2 scanners cannot do this and you may require a good obd2 scanner, depending on the car model. Always make sure that the OBD2 scanner is compatible with your vehicle before you are making any purchase.

6. Erase the P0507 code and go for a test drive to verify that the P0507 code is gone.

7. If the P0507 code is still coming back, the diagnose of EVAP, IAC, EGR, PCV valves etc have to continue. These procedures are more advanced and contact us if you have any questions.

 

Recommended Tools to Fix P0507

To Read the Trouble code memory: FOXWELL NT301 Scan ToolFor basic settings and adaptions, you may need a more advanced OBD2 code reader

Find Air/vacuum leaks: STINGER Brand EVAP Smoke Machine Leak Tester

Car Battery charger: NOCO Genius G3500 6V/12V Smart Battery Charger

 

If you have any other questions about the P0507 code, comment down below and I will answer you as fast as possible. If you have any other car questions you are welcome to ask us at our homepage.

 

To find all OBD2 codes. Check our OBD2 Code List.

Facebooktwittergoogle_plusredditpinterestlinkedinmail
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...

Leave a Reply